FTTH Round Type Plastic Drop Wire Clamp – Product Overview


Cable clamps for FTTH installation (FTTH Round Type) are strong enough to be used outdoors to support aerial FTTH drop cables. These clamps have a proven history of providing long-term support for round FTTH drop cables in aerial installations by providing high levels of tensile strength, environmental resistance to UV rays, and environmental protection from sub-zero temperatures.
When selecting a drop wire clamp for your FTTH installation, use one that provides a high level of tensile strength that is suitable for harsh outdoor conditions. The Unigreat FTTH Round Type Plastic Drop Wire Clamp has a higher pulling force than many other drop wire clamps that have an expected tensile strength of 0.8-1.2 kN. The Unigreat FTTH Round Type Plastic Drop Wire Clamp has a typical pulling force of 1.3-1.5 kN and is designed to withstand: Winds Loads (including ice and snow) Sudden mechanical tension. The increased tensile strength of the Unigreat FTTH Round Type Plastic Drop Wire Clamp is necessary when there are long spans of cable being installed by telecom operators.
Extreme Weather Resistance of the FTTH Round Type Plastic Drop Wire Clamp
The FTTH Round Type Plastic Drop Wire Clamps are specifically designed to withstand extreme weather conditions. Aerial FTTH installations are often affected by large fluctuations in temperature.
The Unigreat FTTH Round Type Plastic Drop Wire Clamp is designed to perform under extremely cold climatic conditions, providing complete protection for the integrity of the drop cables during long, cold winters, periods of extreme humidity (high humidity), and periods of intense UV radiation.
Unigreat FTTH Round Type Plastic Drop Wire Clamp's high-quality PA6 / PA66 Nylon body, for example, contains both Virgin and Recycled nylon, with additives for superior UV protection against degradation caused by the sun, and enhanced longevity to prevent the development of brittleness and fatigue of materials in the field.
Approved for Use by Major Telecom Operators
A wide variety of telecom companies choose the Unigreat FTTH Round Type Plastic Drop Wire Clamp for their FTTH drop cable deployment needs. Many of the telecom companies that have purchased the FTTH Round Type Plastic Drop Wire Clamp from Unigreat are Major Telecom Operators such as Verizon, (USA); AT&T, (USA); and Bell Canada.
Structural Benefits of the FTTH Round Type Plastic Drop Wire Clamp
The clamp's Optimized Circular Cable Winding Structure is also designed to enhance friction created by its Circular Winding Path, allowing the following benefits to occur:
Mechanical Grip – Increases grip of wire
Prevents wire from slipping while under weight
Minimizing Micro-bending & Signal Loss to Fiber – By securing with the clamp, the cable is held securely without damaging the fiber
90 Degree Cable Outlet Design
90 Degree Cable Outlet Design for Routing Cables Around Corners and Bends – The unique 90-degree exit keeps all wires in line with the building when it wraps around corners, poles, walls, etc., thus maintaining minimum Bending Radius of Optical Safe Fiber.
User-Friendly Buckle Mechanism
This product provides a user-friendly buckle mechanism for Easy/Quick Installation:
Open Bail Buckle Structure
No Tools Required
Quick Tensioning & Re-positioning
When combined with this product, users can install/position toners on site quickly and easily.
Cable Compatibility
FTTH Round Type Plastic Drop Wire Clamp Supports:
FTTH Drop Cable 2mm to 6mm (Standard FTTH Drop Wires)
FTTH Flat Drop Cable 2mm to 8mm (Extended Compatibility)
This allows operators to have One Clamp for Multiple Types of FTTH Cables.
Customization Options
To accommodate various projects and plans, Unigreat offers:
Custom colors (Black, Grey, White or Customer Request)
Private Labeling / OEM
Customized Tensile Specs
Materials Upgrades (PA66 Reinforced)
Integration into OEM supply chains for large-scale deployments
Installation Method




1. (a) Position the bail of the clamp in the open position; (b) insert the free end of the cable span into the clamp at "A".
2. Wrap the cable around the mandrel so that it completely covers the mandrel with three full turns of the cable (for example, a 4mm drop cable); the drop cable will discharge from the clamp at "B". The section of cable from "B" onward is unencumbered with mechanical loads, therefore the cable can be fastened to a wall, pole fitting or run to another drop clamp for doubling dead endings.
3. Adjust tension on the span side using the following steps: (1) Push cable at "A" and pull cable at "B" as indicated by the arrows to adjust tension, then (2) continue to adjust tension on span side if necessary.
4. Two-way installations supported; cables may also be laid from "B" to "A' depending on site conditions.
Model Information
Product SKU = UG-A08O
Size = 200 x 27 x 27 mm
Material: PA6 or PA66
Product Weight: 46.7g
Product Breaking Load = 1.5KN
Product Cable Diameter = 2mm - 8mm
Product Warranty = 10 Years
Applications of the FTTH Round Type Plastic Drop Wire Clamp
The FTTH Round Type Plastic Drop Wire Clamp is ideal for:
Supporting FTTH Drop Cable Tensioning Between the Building Facade and Aerial Span
Pole-to-House installations
Fiber To Room / Fiber To Drop Applications
All Telecom Operators
ISPs
System Integrators
Fiber Contractors
It offers excellent mechanical strength and weather resistance.
Summary
The Unigreat FTTH Round Type Plastic Drop Wire Clamp provides:
High-Tensile Performance
Durability
UV Protection
Ease of Installation
This makes it an essential component to successfully deploy reliable FTTH cable through the aerial environment.
For those Operators Looking for An Affordable High-Quality Long-Lasting Drop Wire Clamp with a Proven Reliable Field Performance History, THIS IS YOUR PRODUCT.
Product Specification – FTTH Round Type Plastic Drop Wire Clamp
| Item | Details |
|---|---|
| Company Name | Unigreat |
| Product Name | FTTH Round Type Plastic Drop Wire Clamp |
| Material | Nylon (PA6 or PA66) |
| Applicability | FTTH Aerial Cable Tensioning |
| Cable Diameter | Round: 2mm – 6mmFlat: 2mm – 8mm |
| Tensile Load | Approx. 1.3 – 1.5 kN |
| Manufacturing Process | Injection Molding |
| Product Weight | 41g – 46g |
| Color | Black (Customizable) |
| Warranty | 10 Years |
| Minimum Order Quantity | 1000 Pieces |
| Port of Origin | Shenzhen |
| Product Dimensions | 14 × 7.5 × 3 cm |
Hot Tags: Drop Wire Clamp for FTTH Round Cable, FTTH Round Cable Drop Wire Clamp, adss clamp, ftth drop cable clamp, ftth clamp, fiber cable clamp, stainless steel drop wire clamp, ftth round plastic drop wire clamp
